These are the replacement Wheel Hub Ball Bearings for / the Traxxas Nitro Revo Monster Truck. / / FEATURES: Stainless Steel Construction / Blue Rubber Sealed / / INCLUDES: Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings / / REQUIRES: Assembly onto Vehicle / / SPECS: Outer Diameter: 18mm (0.70″”) / Inner Diameter: 12mm (0.47″”) / Thickness: 4mm (0.15″”)
…
Buy Ball Bearing, 12×18x4mm:TMX 3.3, Revo ,EMX,SLY at Amazon
This is a package of six 2×6mm Traxxas Roundhead Self Tapping Screws. / / FEATURES: Steel construction, silver in color / Used on the Traxxas Revo monster truck, can also be used in any / application where a 2×6mm roundhead self tapping screw is required / / INCLUDES: Six 2×6mm Traxxas Countersunk Hex Screws / / REQUIRES: Small phillips screwdriver, DTXR0170 / / SPECS: Length: 6mm / Diameter: 2mm / / jxs 6/29/04 / ir/jxs
…
Buy Round Head Self Tapping Screw 2×6mm Revo TRA2674 at Amazon
This is the Large Rod End Set for the Traxxas Revo, TRAC71**. / / FEATURES: Plastic construction / Black in color / Metal Pivot Balls / / INCLUDES: 12 Rod Ends / 12 Pivot Balls / / REQUIRES: Assembly to vehicle / / SPECS: Length: 22mm (.88″”) / Width at ball joint: 10mm (.39″”) / / jpg 8/25/04 / ir/jxs
This is a package of six 3×10mm Traxxas Cap Head Screws. / / FEATURES: Steel construction, Black in color / Used on the Traxxas Revo monster truck, can also be used in any / application where a 3×10mm cap head screw is required / / INCLUDES: Six 3×15mm Traxxas Cap Head Screws / / REQUIRES: 2.5mm hex head wrench, GPMR8012 / / SPECS: Length: 15mm / Diameter: 3mm / / Updated JBM 5-17-06 / jxs 6/29/04 / ir/jxs
…
Buy Cap Head Machine Screw 3×10mm No Washer Revo TRA2587 at Amazon
Aluminum rocker posts save 16 grams over the stock steel rocker posts without sacrificing strength. They’re a great addition to any Revo or Slayer that’s being trimmed out for the track.
…
Buy Rocker Arm Post,Aluminum: Revo, Revo 3.3,SLY at Amazon
This is the Chassis Brace for the Traxxas Revo 3.3, TRAC77**. / / FEATURES: Constructed of 0.12″” (3mm) thick 6061 T-6 aluminum / Anodized blue in color / / INCLUDES: Chassis Brace and 4×16mm hex head screw / / REQUIRES: Installing on left side of chassis underneath engine / / jxs 6/08/06 / ir/jxs
This is the 4×10mm BCS Throttle Servo Mount from Traxxas. / / FEATURES: Nylon construction, black in color / / INCLUDES: One Throttle Servo Mount / Two 4×10 Socket Head Screws / / REQUIRES: Installation / / SPECS: Length: 80mm (3.15″) / Width: 27mm (1.06″) / Height: 20mm (0.79″)
These rear drive cups are engineered exclusively for use with the combination of Traxxas steel constant-velocity driveshafts (#TRA5451R) and the adjustable wheelbase rear suspension arm set (#TRA5333R) on Revo. These specially designed drive cups help keep the shafts securely in place throughout the huge range of suspension movement and extreme driveshaft angles allowed by the adjustable wheelbase suspension arms. Note: These drive cups should not be used with standard wheelbase…
Buy Inner Drive Cups : Revo at Amazon
Constant velocity (CV) driveshafts concentrate mass for less overall rotational mass than the stock driveshafts. This results in even quicker acceleration. Both the inner and outer joints anre lubricated and sealed by rubber boots to reduce maintenance and project against wear caused by dirt and grime. The U-joint pins are held captive by the ball bearings so there’s never a worry about losing a pin.
The optional center differential can be installed on Revo 2.5R* or 3.3 to help balance the distribution of power to reduce front end lift on acceleration and improve steering responsiveness. *Requires short-rear output shaft, part #TRA5416, for use with Revo 2.5R standard chassis.
Powered by Yahoo! Answers
